Ashish Imports

Opc Drum For Z- Brother Dr 1020/2030/2140/3100/2130/5440

Specification:

Opc Drum Available Below Model Tn – 2150: Brother Hl2140/2150N / 2170 / 7030 / 7040 / 7840 / 7450/7340/7440/2822 / Tn-2125 / Tn 2120/Tn2175 , Zigma - Tn – 2025 : Brother -2030,2040,2045.2070N,2920/2820/2910, /Lj20001 Aj2000Pro.Mg3220.Mg7130N,Mg7120,Mg7120Pro. M7020Pr0,Mg 7030 (Tn-2000/2025/2050/2075 /2035/Tn 25J) Tn-350, Z - Tn - 550 / 620: Brother Hl5140,5150D.5150Dlt.5170Dn,5130, 5240. 5250,5270/5280. Mfc 8220,8440, 8840D. 8820 Dn.8460,8860,8870. Dcp -8060.8065 (Dr520.3100,3150,3115, 117. 550,580. 3135,3175, 3185) Brother Dcp- 8040.8045D" Hl 5340D,5350Dn,5370Dw,5380Dn / Dcp 8085 / 8080 / 8370 / 8380/8460/8480 / 8660 / 8670 / 8680/8860/8690/8870/8880/8890; Lj3500/3550/3600 ; Tn3130/Tn3280 / Tn3135/3290/Tn3145/3170/3190/3235/3175 / Tn3250/3285 / Tn 3230 , Z- Tn1020: Hl1118 / Mfc - 1811, Dcp-1511 , Z- Tn 720 / 750: Brother Hl-5440D/5445D/5450/5453/5470/5472/ 6180; Mfc - 8510D/ 8515/8520/8710/8712/8810/ 8910/8910/8912/8950; Dcp8110 / 8150/8152/8155/8157/ 8250, Z - Tn – 430: Brother -1030.1230.1240.1250.1270.1400.1430. 1435.1440.1450.1470.P2500 5750,8300,8500,8600.8700.9600,9650,9660,9700,9750,9760. 9800.9850,9860,9870,9880, Z - Tn – 540: Brother Hl-1650.1670N,1850,1870N,5030.5040. 5050,5070N,5130,5140,5150D. 5170D,Mfc 8420, &820D,8820Dn,8220/8840.Dcp8020,8025D,8040. 80450,8045 , Z-Tn2250: Hl 2130/2132/2210/2220/2230/2240/2242/2250 / 2260 / 2270/2280; Dcp-7055/7057/7060/7065/7070;2890/2940/2950/2990; Lj2400/2600/2650/7400/7450/7600/7650 ; Tn2135/ Tn2230 / Tn2215 / 2275 / Tn 2235 / Tn 2260,Z- Dr1020: Hl1118 / Mfc - 1811, Dcp-1511

Features:

• High yield drum
• Sharp copy
• Crystal clear image

Here’s an image of the Epson 6711 (T6711) maintenance box chip, which is the small green PCB (printed circuit board) that attaches to the maintenance (waste ink) tank. It communicates with your printer to track ink absorption levels.
---
What Is the Epson 6711 Maintenance Chip?
The chip monitors the fill status of the waste ink tank (maintenance box). When levels reach full, it stops the printer to prevent overflow and errors.
Upon installing a new or cleaned maintenance box, the chip should reset so the printer sees it as "new" (0% capacity) and allows continued printing.

---
How the Resetter Works
A chip resetter is a small device—often battery-powered—that resets the maintenance chip's counter:
1. Connect the resetter's pins to the corresponding contacts on the chip.
2. The LED indicator flashes red during communication, then turns green upon successful reset.
3. Once reset, the chip shows 0% used (“new” status) and can be reinstalled in the printer.

Note: Resetters must be used before the chip reaches about 85–85% capacity (some vendors say 15% remaining) to be effective. After that, the chip may not reset.
---
Compatible Models & Chips
The T6711 chip is compatible with a wide range of Epson printers, including (but not limited to):
Epson Ecotank ET‑16500, WorkForce WF‑3010, WF‑3520, WF‑3530, WF‑3540, WF‑3620, WF‑3640, WF‑7110, WF‑7210, WF‑7610, WF‑7620, WF‑7710, WF‑7715, WF‑7720
Other models: L1455, WP‑4010/15/25/30/40 series, PX‑B750F, Workforce C8190DW, C8610DWF, C8690DWF, C869R, etc.

---
Using the Resetter: Step-by-Step
1. Power off the printer and remove the maintenance tank.
2. Locate the chip on the tank and align the resetter pins properly—avoid contacting pins marked “no contact.”
3. Press the resetter until the red LED flashes, then observe a green light indicating a successful reset.
4. Reinstall the tank into the printer and resume printing.

The T04D1 chip (OEM designation: C13T04D100) is mounted onto Epson maintenance (waste ink) boxes. It tracks the waste ink level and signals the printer when the tank is full and requires replacement. When triggered, the printer typically locks operations to prevent overflow.

The maintenance box, which houses this chip, collects ink flushed from the system during cleaning cycles. The chip ensures proper monitoring.

---

Compatibility

The T04D1 chip supports a wide array of Epson models. These include:

EcoTank & L-Series: L6160, L6168, L6170/71/78, L6190/91/98, L5190, ET-2700/2750/2756/3700/3750/4750, and ET-15000 among others.

EcoTank Monochrome: ET-M1100/1120/1140/1170/1180/1190 and M2100/2140/2170/3100/3140/3170/3180.

Expression & WorkForce Series: XP-5100/5105/5115; WF-2800/2860/2865.

These models either include the T04D1 box by default or are compatible as replacement parts.

---

How It Works & Resetting the Chip

1. Function: The chip monitors the absorption capacity of the internal felt in the tank. Once saturated, it halts printer usage until reset or replacement.

2. Resetting: With a compatible chip resetter (USB-powered or battery), you can reset the chip so the printer recognizes the tank as "new" (0% used).

Bioprinter's resetter uses internal battery power. LED transitions from red to green indicate a successful reset.

OctoInk’s resetter works via USB-C/Micro and supports T04D1 along with other chip versions. It resets even if the chip reads “full.”

InkStation’s resetter requires the maintenance box to have at least 15% capacity remaining to function.

3. Important: Resetting only resets the electronic count—it does not unclog or refresh the actual waste ink pads. Reusing a full box without cleaning can lead to ink overflow, even if the chip says “empty.”

---

Maintenance & Replacement Tips

The chip is clip-mounted and can be removed and replaced separately. You don’t always need to discard the whole tank if the rest is functional.

Some earlier models (e.g., certain ET‑2850 units) lack a chip; resetting may require proprietary software via authorized service centers. In such cases, even if a compatible box is installed, the counter won’t update automatically.

The T6193 chip is an electronic component, also known as the maintenance tank chip or waste ink tank chip, used in Epson SureColor large-format printers.

Primary Functions:

Ink Monitoring: It tracks how much waste ink the maintenance box (waste tank) has collected.

Communication: Sends that data to the printer, enabling the printer to detect when the tank is near capacity and trigger alerts or errors if needed.

Reset Support: When the tank is replaced—or the chip is reset—the chip counter resets, allowing the printer to accept the tank again.

Product Description Highlights:

Typically comes as a one-time-use chip, although resettable versions (ARC chips) also exist .

Often pre-installed on replacement maintenance boxes for easy plug-and-play usage .

Made from durable materials with reliable recognition—many manufacturers claim 99.9% printer recognition accuracy .

Designed to prevent ink overflow and internal contamination by ensuring accurate waste tracking and timely replacements .

Compatibility:

Works with a wide range of Epson SureColor models, including (but not limited to):

T‑series: T3000, T3200, T5000, T5200, T7000, T7200, T3270, T5270, T7270 .

F‑series and B‑series models (e.g. F6000, F7000, B6080, B7080) .

Physical & Technical Characteristics:

Form Factor: Small PCB easily clipped onto or embedded in the waste ink box.

Chip Type: Intelligent recognition chip; some variants are ARC (auto-reset chips), which automatically reset themselves when reinstalled .

Installation: Tool-free—clips on and gets replaced or reset as required .

---

How It Works in Practice

1. Installation: The maintenance box enters the printer with this chip.

2. Monitoring: As the printer performs maintenance tasks (like printhead cleaning), ink is deposited into the box and tracked by the chip.

3. Alert: Once the ink level approaches the chip’s limit, the printer displays a warning or stops printing.

4. Reset or Replace: Either reset the chip using a specialized resetter tool or replace the entire box with a new chip-equipped one.

Here are some images of the SC26MB maintenance chip (also referred to as C13S210115 maintenance chip) used in Epson printers. This chip is typically attached to the maintenance/waste ink tank to manage the ink level detection and resetting process.
---
What Is the SC26MB Maintenance Chip?
The SC26MB (C13S210115) is a maintenance box chip designed for certain Epson SureColor T and P‑series printers. It resides on the waste ink tank and tracks how much ink has accumulated. .
When the printer detects that the maintenance tank is nearly full, a warning is displayed. Replacing the maintenance tank or resetting the chip stops the warning and allows continued operation without requiring service.

---
Variants & Uses
1. Single-Use Maintenance Box Chip
A throwaway chip intended for one-time use; it resets the ink counter when the tank is replaced.
2. Resettable Maintenance Chip (Chip Resetter)
These are reusable chips that can be reset multiple times (in some cases, unlimited). They're a cost-effective alternative to frequently replacing the entire maintenance tank.
One example is the COLORTIME QE‑SC26MB‑E, a resettable chip supporting numerous printer series across regions—including Asia-Pacific like India. It’s resettable and compatible with many SureColor models.
Another option: QE‑SC26MB‑MA, a chip resetter explicitly for the SC26MB/C13S210115 maintenance model, also offering unlimited reset capability.
The QE‑P8580‑MA resetter allows resetting the chip when the maintenance tank is about 15% full. It signals reset completion via a red‑to‑green indicator light.

---
Compatibility: Printer Models
The SC26MB maintenance chip is compatible with numerous Epson SureColor printers, such as:
Asia‑Pacific models (including India): T3730DR, P6530D/DE/E, P8530DL, T3730DE/E, T7730DL
Other regions:
Chinese versions: T3780DR, P6580D/E, P8580DL, T7780DL, P11080D
Europe/Middle‑East/Africa: T3700DR, P6500 series, P8500DL, T7700DL
Americas: T3770DR, P6570 series, P8570DL, T7770DL
Others: South Korea, Hong Kong, Japan, Australia have equivalent models supported.
Another source confirms compatibility with P8500, P6580, P8580, T7700, T7750, T7780 series.

The T6997 is a one-time-use, disposable chip designed for Epson SureColor large-format printers (e.g., P6000, P7000, P8000, P9000, and related Plus or extended models) .

Primary Purpose:

It monitors the waste ink maintenance tank, tracking when the tank reaches capacity.

Once the printer detects the maintenance tank is full, this chip will trigger an alert or warning, often preventing further printing until the tank is replaced .

---

Where It Fits

The chip is part of or attached to the maintenance (waste ink) tank, which collects excess ink during cleaning cycles and printing.

In some variants, it comes as part of a maintenance tank with chip, replacing both the tank and the chip at once .

---

Key Features

Feature Details

Type Disposable, one-time-use chip
Function Tracks ink waste levels, signals printer when to replace the maintenance tank
Compatibility Epson SureColor P6000, P7000, P8000, P9000 series (and extended Plus variants)
Packaging Neutral packaging; chips may be sold standalone or with tank
Typical Cost Around USD 3 for chip only, up to USD 12–15 when bundled with tank

---

Optional: Resetter Devices

Some suppliers also offer resetter tools for the T6997 chip. These tools can reset the chip so it appears as unused, allowing continued use of the same maintenance tank (though that carries risks of overflow and printer damage if overused) .

These resetters may be battery-powered or USB-powered and are often labeled as unlimited-reset devices.

---

Summary (Plain Explanation)

Think of the T6997 chip as a sentinel monitoring your printer’s waste ink tank.

It’s pre-installed on new tanks and prevents further printing once the tank seems full, protecting your printer from ink overflow.

After replacing the tank, you swap in a new T6997 chip, allowing normal operation to resume.

Although resetter tools exist, the intended use is one-time replacement only.

Leveraging on our rich vendor base, we put forth Gear Spare Parts. These parts are procured from the reliable vendors, who manufacture it using high quality raw material. Clients acclaim these parts for their features like low maintenance, reliability and competitive prices. These products are manufactured using high quality raw materials to provide our client with best in class products.

• Alkali-soluble
• Heat resistant
• Solvent resistant

• Rugged construction
• Dimensionally stable
• Corrosion resistance

• The wiper blade is a small but essential part of a laser‑printer toner cartridge (or imaging unit) whose job is to clean residual toner off the surface of the imaging drum (the OPC drum) after the toner image has been transferred (or at the end of the cycle) and before the next cycle begins. For example, replacement part listings show one for “HP 28A/26A/77A/287A” cartridges. 

• Its typical placement: after the drum has transferred the toner to paper and before the next image is formed, the wiper blade scrapes or wipes off leftover toner so it doesn’t contaminate the next print. Without proper cleaning, residual toner can cause defects (background shading, streaks, spots).

• Material / construction: Usually a thin flexible strip (metal backing + rubber/silicone or polyurethane edge) fixed to the cartridge or imaging unit housing. The edge contacts the drum surface and wipes off the residue.

• Functionally, when the drum rotates, the wiper blade sits flush against it and scrapes off any remaining toner. That toner is then routed into a waste‑toner chamber or container inside the cartridge. If the blade is worn, improperly seated, or damaged, the cleaning will be incomplete and print quality will suffer.